CREATE BOOTABLE USB WINDOWS 7 INSTALL FOR WINDOWS 10

woeusb-x.x.x.bash -target-filesystem NTFS -device Windows10.iso /dev/sd X # for Windows 10

The device should have the form /dev/sd X where X is a letter of the alphabet, and in step 7 you must replace the X with the correct letter of the alphabet that you found in Disks. Open the disks application and make a note of the Device to be used later in step 7. If there are any files on the USB flash drive back them up to a different device. Open the terminal and change locations with cd to the directory that contains woeusb-x.x.x.bash. Right-click the woeusb-x.x.x.bash file that you downloaded, select Properties, and under the Permissions tab put a check in the checkbox before where it says Allow executing file as program. Visit the WoeUSB GitHub page and look for a file with the form woeusb-x.x.x.bash (example: woeusb-5.2.2.bash).Дownload woeusb-x.x.x.bash (example: wget but the latest version may be different from 5.2.2). NTFS filesystem support has been added to WoeUSB 3.0.0 and later. Some third-party installers feature Windows installation images ( /sources/install.wim) greater than 4GB making FAT32 as target filesystem impossible. WoeUSB is an updated fork of the WinUSB project. Native UEFI booting is supported for Windows 7 and later images. WoeUSB is a tool for creating a bootable USB flash drive used for installing Windows.

CREATE BOOTABLE USB WINDOWS 7 INSTALL ISO

The -target-filesystem NTFS flag is required if the installation image is greater than 4GB, which is the case for the current Windows 10 official ISO file. sudo woeusb -target-filesystem NTFS -device /path/to/your.iso /dev/sdX

CREATE BOOTABLE USB WINDOWS 7 INSTALL HOW TO

In the command below replace the X in /dev/sdX with your usb device path (see above how to find it). Writing the ISOДЄfter installation, write the windows ISO to your storage device with the following command. Identify your usb device and see which path it has (like /dev/sdX). You might try one of these: sudo lsblk -scsi -paths There are several commands available to list storage devices. Search for a programm called disks, or if you use gnome you can launch it by executing gnome-disks. Identifying the USB stick (the /dev/sdX path) Sudo add-apt-repository ppa:nilarimogard/webupd8 It does not uninstall grub-efi anymore! вћ Ubuntu / Debian sudo add-apt-repository universe # contains the p7zip-full dependency TLDR: sudo woeusb -target-filesystem NTFS -device /path/to/your.iso /dev/sdX But there is a working fork called WoeUSB. Some answers are outdated, since WinUSB is not working anymore. However this does not guarantee successful installation of Windows. When properly used with a compatible target operating system, both of these methods should get you a bootable USB drive. Source: My blog post about this can be found at Make a bootable Windows USB from Linux. Select the proper EFI loader from your BIOS.Don't forget to unmount (safely remove) the USB drive.If you're making a Windows 7 USB, copy the boot folder from efi/microsoft/ to efi folder.From here extract bootmgfw.efi somewhere, rename it to bootењ†4.efi (or bootia32.efi for supported 32 bits OS ) and put it on USB in efi/boot/ folder.

CREATE BOOTABLE USB WINDOWS 7 INSTALL ARCHIVE

Otherwise, open sources/install.wim with the Archive Manager (you must have 7z installed) and browse to.

If there's a file bootењ†4.efi ( bootia32.efi) then you're done.

Mount your Windows ISO or DVD and copy all its files to the USB drive.

Create a new primary partition and format it as FAT32.

Using GParted, rewrite the partition table of the USB drive as GPT.

I suggest reading the Microsoft UEFI Firmware page. * Older Windows versions / editions may not be properly supported or not supported at all. Now to use it, restart your PC, and boot from the USB drive. echo 'If you see this, you have successfully booted from USB :)' Write this into the file, replacing with the UUID you copied down in step 2. sudo grub-install -target=i386-pc -boot-directory='//boot' /dev/sdXД¬reate a GRUB config file in the USB drive folder boot/grub/ with the name grub.cfg. dev/sdb, not /dev/sdb1) and replace with the folder where you mounted the USB drive (which could be like /media//). In the below command, replace /dev/sdX with the device (e.g. Go to the USB drive, and if the folder named boot has uppercase characters, make them all lowercase by renaming it. Mount your Windows ISO or DVD and copy all its files to the USB drive. Copy the UUID somewhere as you will need it. In GParted, right click the USB partition and select Information. Using GParted, rewrite the USB drive's partition table as msdos, format it as NTFS, and then 'Manage flags' and add the boot flag.

CREATE BOOTABLE USB WINDOWS 7 INSTALL INSTALL

Install GParted, GRUB, 7z, and NTFS on Ubuntu with: sudo apt-get install gparted grub-pc-bin p7zip-full ntfs-3g Even other Linux distros as long as GParted and GRUB are installed.

Create bootable usb windows 7 install